Expert HVAC solutions for homes and businesses across Alamo, CA. Certified technicians, transparent pricing, and results you can count on.
Browse our full range of heating, cooling, and air quality services available in your area.
Upgrading to a modern heat pump delivers dual-mode heating and cooling from a single system, with top-tier models achieving 10+ HSPF and 20+ SEER2 ratings. Proper installation includes Manual J load calculations, refrigerant line sizing, and electrical panel verification for reliable year-round comfort.
Installing a mini-split system correctly requires precise wall penetration, vacuum-sealed refrigerant lines, and proper electrical isolation between indoor and outdoor units. Our technicians size each zone independently using BTU calculations to ensure consistent temperature control across every room.
A complete HVAC installation addresses every component in the comfort chain, from the air handler and condensing unit to the thermostat and ductwork. Technicians ensure proper airflow, verify refrigerant charge, and test all safety controls before handoff to guarantee reliable, code-compliant operation.
When your heat pump struggles to maintain temperature or runs continuously without reaching setpoint, the problem often traces to refrigerant leaks, failing capacitors, or degraded reversing valves. Skilled technicians restore rated HSPF and SEER performance through systematic component-level troubleshooting.
Mini-split repair demands familiarity with variable-speed compressor technology and manufacturer-specific diagnostic protocols from Mitsubishi, Fujitsu, Daikin, and LG. Technicians trace electrical faults, recharge refrigerant to factory specifications, and replace condensate pumps to restore silent, efficient operation.
Comprehensive HVAC inspections cover thermostat operation, ductwork condition, refrigerant levels, electrical connections, and combustion safety. This detailed assessment identifies efficiency losses, safety hazards, and components nearing end of service life before they result in costly emergency repairs.
Clean ductwork directly impacts the efficiency of your HVAC system by reducing static pressure and allowing unrestricted airflow to every register. Our technicians inspect for microbial growth, seal access points after service, and verify airflow improvements with anemometer readings post-cleaning.
An annual air conditioning tune-up catches refrigerant leaks, worn contactor points, and degraded fan motors before they cascade into compressor damage. Technicians measure temperature differential across the coil, verify amp draws, and confirm proper subcooling to protect your investment.
Maintaining safe and efficient boiler operation requires precise attention to water chemistry, flue gas temperatures, and combustion efficiency. Professional repair addresses leaking heat exchangers, malfunctioning aquastats, air-bound radiators, and ignition system failures to restore rated AFUE output.
Scheduling professional furnace maintenance each fall ensures your heating system delivers full BTU output without wasting fuel. Technicians inspect the inducer motor, verify pressure switch operation, calibrate gas valve output, and clean the burner assembly for reliable cold-weather performance.
Upgrading to a smart thermostat enables precise scheduling, remote access, and energy usage reporting that can reduce heating and cooling costs by 10 to 15 percent. Professional installation ensures correct wiring to your HVAC system, including C-wire verification and multi-stage equipment compatibility.
Ductwork problems manifest as uneven room temperatures, excessive dust near registers, and HVAC systems that run continuously without satisfying the thermostat. Technicians identify crushed flex runs, separated joints, and deteriorated mastic seals using pressure testing and visual inspection protocols.
HVAC emergencies do not follow business hours, and a failed system in extreme temperatures puts your household at risk. Our technicians carry common replacement parts including capacitors, contactors, ignitors, and fan motors to resolve most failures in a single visit and restore comfort fast.
Clogged dryer vents are a leading cause of residential fires, with lint buildup restricting exhaust airflow and causing the dryer to overheat. Professional cleaning removes compacted lint from the full vent run, verifies proper airflow velocity, and inspects the exterior termination for damage.
Restoring reliable air conditioning performance requires more than replacing visible parts. Technicians measure refrigerant pressures, check compressor winding resistance, test run and start capacitors, and verify condenser fan operation to ensure every component of the cooling circuit functions within specification.
KIC Refrigeration is trusted by property owners throughout Alamo (pop. 14,411) for a simple reason — we do what we say we are going to do. No inflated repair estimates, no recommending replacements when a repair will do, and no disappearing after the invoice is paid. We are here for the long term and our reputation across Alamo reflects that commitment to honesty.
Our commitment to the Alamo community goes beyond HVAC service. We hire locally, support California suppliers when possible, and stand behind every installation and repair with warranties that actually mean something. When your heating or cooling system needs attention, choose the company that Alamo homeowners already trust with their comfort.
What makes us different from every other heating and cooling company in the area.
Every technician carries EPA Section 608 Universal certification for refrigerant handling — required by federal law for working with R-410A, R-22, R-32, and all regulated refrigerants. Your system is serviced by technicians who handle refrigerants legally and responsibly.
We service Carrier, Trane, Lennox, Rheem, Goodman, Daikin, Mitsubishi, York, Bryant, and every other major residential and commercial HVAC brand. One call handles any system regardless of manufacturer, refrigerant type, or equipment age.
You receive a written estimate with itemized parts and labor costs before any work begins, and the final invoice matches. No diagnostic fees hidden in the repair bill, no surprise surcharges — just honest pricing you can verify and trust.
We carry full general liability and workers compensation coverage on every job. Our HVAC license is current in every state we operate, and we pull permits when local codes require them. Your property and our crew are fully protected on every visit.
If the repair does not solve the problem or the installation does not perform to specification, we come back and make it right at no additional cost. Our guarantee covers workmanship, parts, and system performance because half-finished work is not in our vocabulary.
Get the information you need to make confident HVAC decisions for your property.
Heat pumps offer both heating and cooling from a single outdoor unit, making them significantly more energy-efficient than furnaces for moderate climates. A heat pump does not generate heat — it transfers it from outdoor air, which requires far less energy than burning gas or running electric resistance coils. Modern cold-climate heat pumps with variable-speed inverter compressors operate effectively down to minus 15 degrees Fahrenheit, making them viable in most California locations. For Alamo homeowners with natural gas access, a dual-fuel system — heat pump for primary heating paired with a gas furnace for backup during extreme cold — often provides the best balance of efficiency and performance. Heat pumps also qualify for federal tax credits under the Inflation Reduction Act. KIC Refrigeration evaluates your specific climate zone, insulation levels, and utility rates to determine whether a heat pump, furnace, or dual-fuel system is the smartest investment.
Most residential HVAC installations in Alamo, CA are completed in 1 to 3 days depending on the system type, condition of existing ductwork, and complexity of the project. A straightforward furnace and air conditioner replacement on existing ductwork typically takes a single day — our crews arrive in the morning and commission the new system by afternoon. Heat pump conversions, ductless multi-zone installations with line sets routed through walls, and projects requiring new or modified ductwork may take 2 to 3 days. Commercial installations and whole-building systems can extend to a week. We schedule around your availability, coordinate all permits and inspections, and protect your flooring and walls throughout the process. Every installation concludes with a full system commissioning including airflow verification and refrigerant charge confirmation.
Yes. KIC Refrigeration provides around-the-clock emergency heating and cooling repair throughout Alamo and surrounding California communities. Whether your furnace fails during a cold snap and pipes are at risk of freezing, your air conditioner dies during a dangerous heat wave, or you detect the smell of gas near your equipment, our technicians respond quickly. Every service vehicle carries common replacement parts — capacitors, contactors, ignitors, blower motors, control boards, and refrigerant — so most emergency repairs are completed in a single visit. We do not charge extra trip fees for after-hours calls, and our dispatchers are trained to triage situations over the phone so the right technician arrives with the right equipment. Call us anytime and we will have a crew on the way.
As a guideline for Alamo homeowners, consider replacement when your system is 15 to 20 years old, when the repair cost exceeds 50 percent of a new system, when the equipment uses R-22 refrigerant which is no longer manufactured and costs $100 or more per pound, or when your system runs constantly without adequately heating or cooling your home. Additional indicators include frequent breakdowns — more than two per heating or cooling season — rising utility bills despite regular maintenance, uneven temperatures between rooms, and excessive noise or dust. The age thresholds vary by equipment type: air conditioners and heat pumps typically last 15 to 20 years, furnaces 20 to 25 years, and boilers 25 to 30 years. KIC Refrigeration provides honest repair-versus-replace assessments at every service call, including side-by-side cost projections for both options.
Absolutely. Modern high-efficiency HVAC equipment can reduce heating and cooling costs by 20 to 40 percent compared to systems installed 15 or more years ago. The improvement comes from advances in compressor technology, variable-speed motors, and smarter controls. In Alamo, upgrading from a 10-SEER air conditioner to a 16-SEER2 or higher unit delivers substantial monthly savings — the higher the SEER2 rating, the less electricity consumed per BTU of cooling. On the heating side, replacing an 80-percent AFUE furnace with a 96-percent modulating furnace means that 16 cents of every heating dollar previously wasted up the flue now heats your home. Heat pumps offer even greater efficiency, delivering 2 to 4 times more heating energy than they consume in electricity. KIC Refrigeration calculates projected energy savings for any equipment upgrade so you can see the return on investment before making a decision.
The ideal time for HVAC replacement in Alamo is during the shoulder seasons — spring and fall — when demand is lower, equipment availability is highest, and scheduling is more flexible. Contractors are less booked during these periods, which means faster installation timelines and potentially more competitive pricing. You are also more likely to find manufacturer rebates, utility incentive programs, and promotional financing during off-peak months. From a technical standpoint, moderate temperatures allow your new system to be commissioned and tested under less extreme conditions. However, KIC Refrigeration completes HVAC installations year-round in California and can often start within days of your approved estimate, even during peak summer or winter demand. If your current system is showing signs of failure, do not wait for the perfect season — a planned replacement is always better than an emergency one.
Thousands of satisfied customers — here is what a few of them had to say.
"Mini split repair was done right the first time. The outdoor unit had a refrigerant leak and they found it, fixed it, and recharged the system same day."
"AC repair was fast and fairly priced. The compressor was failing and they had the part on the truck. Done in about ninety minutes."
"HVAC inspection was very thorough. Got a written report with photos and recommendations prioritized by urgency. Helpful for budgeting repairs."
Professional heating and cooling services extending to neighboring cities and towns.